emergency boarding up service up a doorway (heavenarticle.com)

boarding up and burglary repairs up a doorway keeps rain, snow and hail from further damaging the property. It also helps keep vandals, squatters, and scavengers away.

Doors are more secure than windows, but they are still susceptible to being damaged or kicked out. These doors should be set up with composite door frames that won't shift over time.

Measure the Doorway

A doorway is an opening through which you can enter or exit a room, a building, or a passage. The doorway could also function as a portal that provides access to another area for instance, a different room in the same house or other part of the country.

You'll need to measure the doorway. With a tape measure, begin by measuring the width of the frame's inside from one end to the other. It is crucial to remove any trim or brickmould prior to taking the measurement. This will ensure that you're only measuring the frame and not the actual windows or doors. Take these measurements in three places and choose the largest number as the dimensions of the doorway.

If you want to replace the door, measure the width of the door's rough opening. It is possible to do this without removing the old door by prying the old door away from the jamb using a wide pry tool. This will reveal the rough framing which will be used to hang the new door. Measure the height of the opening in three places and use the smallest number to determine the height of the new door.

You can also determine the width of the doorway by running the tape across the edge of the frame in three locations in the center, left and right - and recording the most extensive measurement as the width of the doorway. This is the best method to ensure that your plywood will cover the entire area and allow you to build an entirely new door or window.

Measure the Frame

The act of boarding up windows, doors, and other openings which allow in the elements can offer a substantial amount of security for your home. Begin by carefully examining each window to determine the size and shape. Then, take a measurement of the width of the frame. Note every measurement to ensure that you cut the plywood boards accurately.

Before you start, Boarding up a doorway wear protective gear to safeguard against broken glass and other hazards. It is also recommended to work with a colleague, as it is easier to work with large sheets of plywood with an extra pair of hands.

Use wide masking tape to seal the cracks and remove any panes which cannot be taped. Cover the remaining ones with heavy plastic garbage bags. Seal the trash bags from the inside to increase their strength.

If the frame is still in good shape it is possible to save time by skipping the framing and simply running an additional stud straight across the gap to the midpoint of the window. This will give the frame additional strength without requiring the additional effort of removing and installing the framing itself.

Acquire a few plywood sheets and tools, such as drill, hammer and saw (if cutting is required). Referring to the frame measurements, mark each board with the window number. Then using the pilot holes you made earlier, connect the plywood to the frame.

Measure the Jambs

The jambs are three pieces wood that a door is mounted directly. They're essential in keeping doors shut correctly and should be tight and level. You'll have to adjust the jambs if the jambs aren't level.

Start with the side jambs of the hinge. They have a raised section towards the center, which is known as a doorstop. The doorstop sits on the door slab to prevent it from hitting the frame as it closes. Install a plywood strip to the bottom of each stud, so that it raises the floor inside the opening of the rough by approximately 1/2 inch (photo). This will keep the door from scratching the tile, carpet or throw rug when it is shut and opened.

Remove any trim, molding or casing around the hinge side jamb to get an accurate measurement. This will expose the opening in rough form so that you can accurately measure it.

After you've measured, mark the locations of the hinge holes on both sides of the hinge jamb. With a combination-square, measure the depth of the hinge mortise and adjust the square to match the mark on the hinge jamb. This will ensure that the hinge is centered within the frame and aligned with the door. Repeat the process on the latch jamb side the door. Utilize a nail gun as well as 2-1/2-inch screws to secure the strike side.

Take a look at the Header

A header is a heavy dimension lumber board that is attached to the wall framing. It transfers loads above windows and doors to the studs below. When properly frame, the King and Jack the studs are attached to the opposite side of the header. They also join against the header at both ends to form an extremely sturdy column that carries the weight from the opening to the floor and foundation.

In traditional framed houses, you can use a set of tables in the code to calculate the size of the header for a specific span. The code has tables for three different widths of buildings. Interpolation is a method to determine the appropriate size of the header.

There are better options than the standard 2x12 header. These can save lumber, reduce thermal bridges and allow for more space to be used for insulation. Builder Mike Guertin takes a look at these options and decides if they're the right choice:

He also talks about the rim-board headers that connect an opening without the use of a header. This eliminates an element in framing process, and can result in stronger frames. He also discusses box headers which are more difficult to build however, they offer larger spans than single-ply. He also discusses a fastening schedule for these different headers, which calls for 8d common nails spaced every 3 in.

Cut the Boards

Before the process of boarding up companies a door, it is crucial to thoroughly prepare the area. Clear away furniture and decor to give you ample work space and to avoid damaging belongings. Remove the doorknobs, locks, and other hardware and store them in a secure location for later installation. To increase adhesion, clean the door and frame, and wipe down the entire surface to remove dust and dirt. Sand rough patches, if needed, to ensure that the boards fit securely and provide adequate protection.

Once the doorway is cleared, you can start cutting the plywood. A quality circular saw will make straight cuts and cut through wood with ease, while a jigsaw can deal with the curved surfaces. It is essential to wear protective equipment for this process, which includes a dust mask and safety goggles.

It is crucial to align the board with the frame and jambs once it has been cut to size. For reinforcement, it is a good idea also to add some vertical pieces to the bottom of the board. Once the board has been aligned and secured it is now ready to be put in the desired position.

Boarding up a doorway can help safeguard a home or business from damage and unauthorised entry during a storm, disaster or other occurrence. It can also be used to secure vacant properties or stop thefts and break-ins until the property is reoccupied. The best results can be obtained by analyzing the situation and the need, as well as the type of boarding.

Install the Boards

The boards should be screwed down with heavy-duty screws, rather than nails. The strength of these fasteners can distribute the pressure and prevent prying, enhancing the effectiveness of your boarding. Weatherstripping or caulk can be used to close the edges and prevent water and wind from infiltrating through the gaps. It's also a good idea to leave a gap for ventilation to avoid stuffy air and moisture buildup.

Wearing gloves and goggles is a must when working with power tools. Also, you should employ a straightedge or pencil to mark your cutting, since mistakes will be more difficult to fix once you've finished cutting. You'll want to make your cuts as precise as you can so that the boards will fit perfectly against the frame and door casing. The jambs and head will require trimming so that they are aligned with the wall.

It is recommended to do this prior to the storm hits so that you have time to secure any other areas that are at risk. A little planning will save you time and will help you prepare your home or business for the possibility of a catastrophe. Your property can be protected from criminal activity, wind and flying debris with the proper preparation. You will also have peace of mind knowing that your property is secure.