Boarding Up Windows And Doors Techniques To Simplify Your Daily Lifethe One Boarding Up Windows And Doors Trick That Every Person Should Know > 자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Boarding Up Windows and Doors Before a Storm Hits

In the event of a storm and your windows are smashed, boarding up services them up and doors provides measurable protection from damage. To do this, you'll should have a few things in hand.

Measure the width and height of the window including the frame (not the trim or masonry that surrounds the window). Note these measurements down so you don't forget them.

Preparation

It is recommended to put up a put up a board on your windows and doors prior to the occurrence of a natural or stormy weather. This will stop property damage and reduce the loss of life. Boarding up windows requires an extensive amount of preparation, such as purchasing and measuring plywood boards and determining the exact size of each window to cover. It also takes time to cut the boards and then install them correctly. It is possible to speed up the process by preparing the boards when you learn of an approaching storm. If you do this, you can avoid a stressful last minute rush and make the process much simpler for you and your staff.

Begin by listening to weather forecasters and following the guidelines laid out by your local government. The earlier you begin the process, boarding up windows and doors you'll have more time to collect the materials and store them without feeling rushed by the approaching storm. Depending on the severity of the imminent event, you may need large quantities of plywood to cover all of your windows. To ensure that you have the right size, you can use a tape measure to determine the width and height of each window opening. Make sure to include the trim or framing around each window, as well as any ledges with extended edges if they are applicable.

Then, determine the size of the plywood sheets you require by dividing your window's total height and width by 2. If your window measures a width of 16 inches, then the thickness of each sheet is 8 inches. If your exterior is made of wood drill pilot holes in the plywood sheet to align with the window frame below. This will reduce splitting when you screw in the screws.

For a window opening that is bigger than what a sheet of plywood can take cut two sheets that are each half the size of the desired window and set them side-byside on the wall. Then cut a piece of 2 by 4 in (5.1 by 10.2 cm) lumber to the length of the connecting edge of the sheets of plywood and lay it over the seam. Then then, drive 2.25 in (5.7 cm) screws through the bracing and into the plywood sheet to join them together.

Materials

To ensure security and safety, commercial boarding up service up windows and doors should be done with only strong materials that will not crack under pressure or splinter during high winds. Plywood is a popular material used to encase windows. It is simple to use, inexpensive and readily available. It's important to choose plywood that is specifically exterior grade (CDX) for extra strength and is free of knots and warping. A sturdier alternative is storm shutters, also known as hurricane shutters, which are installed over existing windows to provide greater protection against shattered glass and weather conditions that can be severe.

Once you've determined the location of the window openings you can determine the height and width to determine the amount of plywood you'll require. Use a power drill create pilot holes in the plywood sheets around each window at intervals of two inches. Before attaching the plywood, you must identify and mark stud locations on the wall to ensure that the boards will be fastened securely. If your home has wood siding, search for nailheads that may indicate the locations of studs. If not, you can look for stud positions using your drill. Screws should be driven into the framing, not into the sheathing or trim. A plywood panel attached to these materials may cause a safety risk during severe winds.

If your window is too large for one sheet of plywood, you could cut two pieces of plywood each half the size and join them with 2 by 4 inches of lumber. Label each plywood panel so that you can identify which window it will be covering.

To affix the plywood panels to the wall, make use of corrosion-resistant screws that are long enough to penetrate both the sheathing and studs. To secure the plywood panels to the wall, use corrosion-resistant screws that are long enough to penetrate both the sheathing and the studs.

You should also consider installing polycarbonate security glass such as DefenseLite on your primary windows. These transparent shields are bonded to existing glazing to safeguard your doors and windows. They are virtually indestructible, preventing criminals from breaking in.

Installation

If you live in a region prone to hurricanes, or are planning on moving to one, the best course of action is to board up your doors and windows before the possibility of a storm is afoot. This project can be completed quickly and efficiently, but only if the plywood panels are measured, cut, and labeled before the storm hits.

You'll need other tools as well which include drills, saws (or a hammer with nails for those who don't have the power tool) and the level, gloves and safety glasses. It's a good idea to coat the plywood with sealant in order to make it waterproof.

Begin by measuring the height and width of each window opening, then cutting your plywood sheets so they can fit inside the frames, with a 4-inch overlap on all sides. It is best to do this on the spot, as it gives you more control over the precise dimensions of the plywood.

Utilize a circular or track saw to cut the boards to size Be aware that you'll have to sand them down after they're installed. Once you've got your boards place, screw 3-inch stainless steel hanger bolts into the framing studs that surround each window. Use washers on each bolt, and wings nuts to ensure they are secured. Make sure that each screw is able to penetrate the studs at a minimum of two inches to ensure the board is strong enough to resist high winds.

If you're building with concrete blocks, you can attach the plywood to the structure using galvanized pan-head screws driven through the edges that overlap of each panel to form masonry blocks or cinder blocks. You'll also need to drill pilots into the masonry before screwing corrosion resistant screws into the holes. This task can take up to three hours per period. It is essential to begin as soon when an alert for hurricanes has been issued. This will give you ample time to finish the job before the storm hits.

Maintenance

If you're a homeowner or business owner, you must have the necessary supplies to put up a board around doors and windows ahead of an extreme storm. This will allow you to avoid costly repairs and safeguard your home from further damage that could be caused by wind, rain flying objects, and other factors.

The appropriate materials can make boarding up and burglary repairs up easier and quicker. The most important thing is to measure the dimensions of the windows you'll need to cover. This will ensure the OSB or plywood fits well and will not be able to slide off easily. If you're using plywood, be sure to use exterior grade sheets and consider adding an additional protective finish.

Once you have the OSB or plywood measured, mark the areas where the screws will go into the board. Make use of a drill to drill holes at 12-inch intervals in the plywood. You can then use hanger bolts to anchor the boards in an emergency boarding up cost or 24 hour emergency boarding up situation. After the storm is over and the local authorities have given the all-clear, take out the bolts but keep them in case of a need in the future.

The next step is to put the plywood panels on top of the windows. This is a two-person task So be prepared prior to starting. If you're using plywood be sure to sand the edges of the piece to smooth them so that they don't scratch paint or cut. Then, nail the frame to the plywood with screws that are corrosion-resistant that fit into the pilot holes. If your home is lined with shingles made of vinyl it is recommended to nail the plywood to the shingles rather than the wood framing beneath.

Besides keeping out rain and other weather elements, a boarded-up window is also an effective method to deter burglaries. Burglars are more likely to attack a building that has a damaged or unlocked window. Also, they are more likely to break into the store with a boarded up window than one without. This is something that business owners in retail should take very seriously.